Search results

  1. M

    CPU running at close to 100%

    Hello I've noticed the CPU load running at close to 100% on my FusionPBX on a Proxmox VM. This only occurred after a recent power outage and subsequent reboot. I did a little diiging and used the command "top" to find out what the culprit is. What steps can I take to calm the cpu usage down...
  2. M

    Cannot dial out or connect

    Hello Everything was working fine 4 days ago and now I can't connect via the GUI nor can I dial out. I've reset the VM instance but I get this error message when trying to login via the GUI. I can SSH into the device. I'm running FusionPBX on a Proxmox VM server. error: SQLSTATE[08006] [7]...
  3. M

    Moving Domains

    Hello I have a small system on a stand alone PC. The domain is "current.fusionpbx.com". I created a VM install of "test.fusionpbx.com" and hand programmed into it everything that was in "current.fushionpbx.com". On the "test.fusionpbx.com" VM I want to replace the FQDN with...
  4. M

    SOLVED SIP Phone Registration

    Hello I have a SIP phone that can register to a stand alone FusionPBX server (192.168.2.25). If I shut that server down and turn on a virtual machine with the exact same ip address (192.168.2.25) as the stand alone, the soft phone will not register? I can ping 192.168.2.25 and I've run a sudo...
  5. M

    Backup and Restore

    Hello I have a backup (automatically generated by FusionPBX) from a Debian 10 machine. Can I restore it to a newly minted Debian 11 machine and if so how do I do it? I don't understand the procedures outlined in this document...
  6. M

    error: could not find driver

    Hello Sorry to post this a second time, but I need to gain access to the FusionPBX GUI. When I enter the IP address of my server (in a browser), I get the following error message: "error: could not find driver". I can SSH into fusionPBX, however I cannot gain access to the web administration...
  7. M

    502 Bad Gateway

    Hello I recently upgraded my FusionPBX from Debian 10 to Debian 11. When I try to access the admin panel via a browser and the IP address, I receive a "502 Bad Gateway" "nginx/1.18.0" error message. The phones are logged into the switch and can make calls plus I can SSH into the system. How do I...
  8. M

    Backup Questions

    Hello I've been reading up on how to do a backup but I found a note that indicates backups are done automatically on a daily basis. I haven't set this up, so I presume this is a function of FusionPBX. When I go into /var/backups/fusionpbx/postgresql I see a "fusionpbx_pgsql_2022-03-16" file...
  9. M

    ZoiPer phone won't register through VPN

    Hello Issue: My ZoiPer phone won't register when I try and connect through a VPN, Background: I'm running OpenVPN on my Ubiquiti Edge router. I can connect successfully and log into FusionPBX, Home Assistant, internal web site and NAS; all with different IP addresses. What I can't figure out...
  10. M

    Gateway Restart

    Hello From time to time the gateway needs to be restarted (due to a power outage). I can't seem to do this from Accounts > Gateway, select my VoIP.ms gateway and press "start" at the top of the screen. Only a reboot will get the gateway to connect. Is there another method I can use instead of...
  11. M

    Rogers Home Phone & FusionPBX Advice.

    Hello I'm thinking of moving my current number over to Rogers Canada Home Phone Service. I believe the equipment they use would deliver the trunk as an analog port off a piece of equipment. Here are my questions and hopefully someone has some experience with this type of service. Let's suspend...
  12. M

    Voicemail Password

    Hello I'm trying to suppress the VM password when anyone dials *700 to check the general delivery mailbox. I've read some of the threads and have created a dialplan, however I still have to input a password to gain access to the mailbox. Can someone kindly point out what is wrong with my...
  13. M

    VM - Skip Instructions

    Hello I have an inbound route to ring group 600. After 30 seconds it times out and transfers to VM 700. I would like the caller to only hear the greeting followed by the beep; I don't wish them to hear any instructions. Is there a way to set this via the GUI and where do I look? I've found...
  14. M

    Voicemail GUI

    Hello This maybe a rookie question, however as a user (user ID 700 / DN 700) I want to be able to administer my voicemail via a GUI. Is this possible? I want to be able to log into my VM and listen to any messages or record / upload a new greeting. Can this be done via the GUI or is VM admin all...
  15. M

    Outnound Route Not Working

    Hello The gateway is registered (voip.ms) and my inbound route is working, however I can't make outbound calls. I have a route setup to use the registered gateway and "North America" as a dial pattern. Is this an issue with ACL and if so then should I have the voip.ms IP address of the gateway...
  16. M

    VoIP.MS Setup

    Hello I'm having difficulty in getting my FusionPBX to make outbound and inbound calls using voip.ms. I have the gateway successfully registered and have created outbound and inbound routes. I've posted a picture of my gateway setup with the username and password blanked out. I have the IP...
  17. M

    VoIP.MS Gateway Setup

    Can anyone comment on how to set up a gateway for voip.ms? Whenever I try and register, I get an error message: "Invalid Profile [external]" Here are the settings I'm using: -Gatewayname: VoIP.ms -Username: Your VoIP.ms account number xxxxxx -Password: The password you used to sign up -From...
  18. M

    Extension to Extension Calling

    Hello I have two softphones on the same network, DN 206 & 207. For some inexplicable reason they cannot call each other. I'm getting an error message in WireShark of " NO_ROUTE_DESTINACTION". I've attached a screen shot of my findings. I must have accidentally changed something in my setup but I...
  19. M

    Destination Ring Groups

    Hello I recently upgrade to 4.5.24 and when I build a dialplan > destination - then select "actions" I've noticed "Ring Groups" isn't in the drop down box. Has it moved or what am I doing incorrectly? Thanks in advance for any help that can be provided.
  20. M

    MicroSIP Softphone Not Registering

    Hello Simple question...I hope! I'm using a MicroSIP softphone that previously could register to my FusionPBX. Now it won't register. I've checked my other soft phones (Zoiper and another MicroSIP softphone) and they won't register either. Each work station can successfully ping the FusionPBX...