Recent content by mc6650

Hello hfoster and thank you for your response. I'm not sure I understand what "I think the unit file needs: After=network.target network-online.target local-fs.target postgresql.service freeswitch.service" means. I used: "systemctl status event_guard.service" to verify if the service was...

That seems to have worked. Thanks very much for the tip. Is there a way to check if "event_guard.service" is running? %CPU CPU NI S TIME COMMAND 0.2 - 0 S 00:00:00 /usr/bin/php /var/www/fusionpbx/app/event_guard/resources/service/event_guard.php 0.3 - - S 00:00:44...

Additional Information: Is it the "event_guard.php" that's tying up the CPU? %CPU CPU NI S TIME COMMAND 0.1 - 0 S 00:00:00 /usr/bin/python3 /usr/bin/fail2ban-server -xf start 0.2 - 0 S 00:00:00 /sbin/init 0.4 - - S 00:00:01 /usr/bin/freeswitch -u www-data -g...

Hello I've noticed the CPU load running at close to 100% on my FusionPBX on a Proxmox VM. This only occurred after a recent power outage and subsequent reboot. I did a little diiging and used the command "top" to find out what the culprit is. What steps can I take to calm the cpu usage down...

I have a relatively small system so I think I'll go ahead and re-install it.

First command I used was ss -nltp | grep postgres Returned nothing. Then: systemctl status postgresql@13-main.service ● postgresql.service - PostgreSQL RDBMS Loaded: loaded (/lib/systemd/system/postgresql.service; enabled; vendor preset: enabled) Active: active (exited) since Sun...

Initial error message psql: error: connection to server at "127.0.0.1", port 5432 failed: Connection refused Is the server running on that host and accepting TCP/IP connections? Then I switch to su and did a: systemctl stop postgresql Followed by a: systemctl start postgresql Then...

Are there any other steps I could try? Would a restore work? Thanks

Further update: I stopped then started the service: root@FusionPBX:~# systemctl stop postgresql root@FusionPBX:~# systemctl start postgresql root@FusionPBX:~# systemctl status postgresql ● postgresql.service - PostgreSQL RDBMS Loaded: loaded (/lib/systemd/system/postgresql.service...

Update: I was reading through some of the forum posts and I did a "netstat -nal". Don't know if that helps. netstat -nal Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 0.0.0.0:80...

Hello postgresql seems to be started. pbx2@FusionPBX:~$ systemctl status postgresql ● postgresql.service - PostgreSQL RDBMS Loaded: loaded (/lib/systemd/system/postgresql.service; enabled; vendor preset: enabled) Active: active (exited) since Fri 2022-08-05 09:48:31 EDT; 3h 42min ago...

Hello Everything was working fine 4 days ago and now I can't connect via the GUI nor can I dial out. I've reset the VM instance but I get this error message when trying to login via the GUI. I can SSH into the device. I'm running FusionPBX on a Proxmox VM server. error: SQLSTATE[08006] [7]...

Hello I have a small system on a stand alone PC. The domain is "current.fusionpbx.com". I created a VM install of "test.fusionpbx.com" and hand programmed into it everything that was in "current.fushionpbx.com". On the "test.fusionpbx.com" VM I want to replace the FQDN with...

I've solved the issue by rebuilding the FusionPBX server on the virtual machine. Thanks for your reply.

Hello I have a SIP phone that can register to a stand alone FusionPBX server (192.168.2.25). If I shut that server down and turn on a virtual machine with the exact same ip address (192.168.2.25) as the stand alone, the soft phone will not register? I can ping 192.168.2.25 and I've run a sudo...