Recent content by kwangmien

Hi All, Our Fusion PBX version is 4.4.6. We ran a VAPT test and found JQuery vulnerablities as below. Can anyone advise : a. How to upgrade to the latest JQuery version ? b. If the JQuery is upgraded to the latest version, will it affect the Fusion PBX ? Thanks Regards Kwang Mien

Hi, Our Fusion PBX is version 4.4.6. We ran a VAPT test and found vulnerabilities for nginx as below. Can anyone advise if i upgrade to version 1.17.7, will there be any impact to Fusion PBX ? Is there other ways to resolve this vulnerabilities without upgrading the nginx ? Thank...

Hi, We are using Fusion PBX version 4.4.6. We ran VAPT test on the PBX and found that there is a "Source Control Management Files accessible" vulnerability. May I know how can these be fixed ? Thanks Regards, Kwang Mien

Hi, I am using Fusion version 4.5.10. The fax that i sent using the Applications=>Fax Server in Fusion will not go through. The scenario is : a. I upload the PDF to be faxed in Fax Server b. When the fax is sent, base on the wireshark capture, the fax call is established. The rtp stream is...

Hi, I checked on the link. Can you advise where do I configure the below in Fusion ? {ignore_early_media=ring_ready}sofia/internal/user@domain

Hi, Thanks for your reply. The issue is when my IP Phone makes a call out to a mobile phone through Fusion PBX, I could not hear the ring back tone. IP Phone -> Fusion PBX -> Local Provider -> mobile phone I understand that Fusion send SIP 183 during the ringing phase for the above call...

Hi, I am using Fusion PBX version 4.5.10 When my IP phone which is registered to Fusion PBX makes an outbound call to an external number, Fusion responded with a SIP 183 Early media to my IP Phone. Can anyone advise how i can configure Fusion PBX to respond with a SIP 180 instead ? Thanks...

Hi , I am using Fusion version 4.4.6 Currently, I have configured call forwarding for extension 127. I have configured to override the caller ID of the forwarded call with 31000717 I have enabled call forward and follow-Me caller ID for the superadmin permission. However, when the call is...

Thanks all. the domain appeared after i input in the domain in the Realm field and restart the gateway.

Hi, I am using Fusion version 4.4.6 In my gateway configuration settings, i have configured a domain in the "From Domain" field as shown below. However, when I made call using the gateway, the INVITE message does not show the domain in the From and To Header. instead it is showing the IP...

Hi, Our Fusion PBX is version 4.5.10. I would like to know how i can disable TLS port in the server. I have tried the below method. However, the TLS port is still open. a. Under Advanced->Variable, for SIP Profile for External and Internal, set internal_ssl_enable and external_ssl_enable to...

Hi, Issue is resolved by adding the ringback in the dialplan for the outbound route.

Hi, Our Fusion PBX version is 4.5.12. I would like to configure the Fusion PBX to send SIP 183 whenever the phone makes an outbound call. I have added the bypass_media_after_bridge and bridge_early_media in the dialplan for one of outbound Routes as below. However when the IP Phone makes...

Hi, I am using Fusion PBX version 4.5.10. When Fusion receives an INVITE with Remote Party ID, it challenge with a SIP 407. Call Scenario : a. Fusion register a SIP Trunk to our core voice server b. There is an incoming call to a DID . c. our core voice server route the call to Fusion PBX d...

Thanks for your reply. currently the user has personal DID. it is just that for call return, the call should be directly routed to user if he has called before.